Equipment Specifications Library

Basic Model Information

  • Manufacturer:
    Rayco
  • Model:
    RG35

View Manufacturers View Models

Additional Info

GENERAL
-Weight: 1830 Lbs Maximum
-Length: 114" Maximum (Arm in storage position)
-Height: 52" Maximum
-Width: 35" Maximum
-Width with Dual Wheels: 52.5" Maximum
-Chip Collection Capacity: 12.5 cu. Ft Minimum
-Chassis Design: Electrically welded 3" x 3" x 3/16" Square Steel Tubing, Formed 1/4" and 3/8" Gr. 80 steel
-Self-Propel Means: Self-propelled with variable speed control and automatic hill brake
-Operator Control Console: Controls mounted On Swing-away Arm with a Fully Covered Valve Bank
-Swing Pivot Bearings: 9" diameter slewing ring
-Brakes: Rear - Spring Applied Hydraulic Release
-Tires: 18 x 8.5-10 R4 4 ply
-Drive Axle Bearings: 1-1/2" flange roller minimum with grease fitting

ENGINE
-Model: Briggs & Stratton Vanguard 35hp Required
-Main Bearings: 2 Minimum
-Number of cylinders: 2
-Bore: 3.36"
-Stroke: 3.40"
-Displacement: 60.5 cu. In Minimum
-Maximum no load RPM: 3600
-Gross HP at maximum no load RPM: 35HP Minimum
-Maximum rated torque: 39.5ft lbs @2500 RPM Minimum
-Cooling medium: Unrestricted Air Flow Required
-Air Cleaner: Heavy Duty, Dual Element, Dry type
-Oil Filter: Spin-on type
-Fuel Tank Capacity: 6.5 gallons Minimum
-Electrical System: 12 volts/15 AMP Alternator Required

HYDRAULIC SYSTEM
-Pump Displacement: 0.62 cu. In. Minimum
-Pump Gallonage @ 3600 RPM: 5.2 GPM
-System Pressure Relief: 2500 PSI Aux / 3500 PSI Drive Minimum
-Oil Tank Capacity: 2 Gallons Minimum
-Oil Filter: 10-Micron Full Flow
-Oil Type: Tellus T46
-Valve: Spring-Centered Series
-Hose Capacity: 3000 PSI Working Pressure
-Swing Cylinder: Minimum 3" Bore, 6" Stroke, 1-1/4" Rod Minimum
-Lift Cylinder: Minimum 2.5" Bore, 8" Stroke, 1-1/4" Rod
-Hydraulic Wheel Drive Motor: 10.4 cu. In/rev
-Drive Chain: 50R Series Minimum
-Fittings: O-ring Required

CUTTING WHEEL
-Wheel Diameter: 17.25" Maximum
-Wheel Thickness: 1" Minimum
-Cutting Wheel Bearings: 1.5" Pillow Block Minimum
-RPM: 1170 Approximately
-Intermediate Belt: Banded "A" type 3-section V-belt
-Drive Chain: Gates Polychain GT, Low Maintenance
-Jackshaft Bearings: 1.5" Pillow Block Minimum
-Cutting Teeth: RAYCO Super tooth forged, One-piece, with tungsten carbide tips
-Cutter Teeth Quantity: 18 Maximum
-Belt Guard: Steel required
-Chip Retaining Curtains: Fabric impregnated rubber
-Cutter Wheel Engagement: Electromagnetic clutch with the "Quick Stop" brake system

CUTTING RANGE (without repositioning)
-Below Ground Level: 12" Minimum
-Above Ground Level: 24.5”Minimum
-Cutting Width: 51" Minimum
-Forward - Backward: Unlimited in Drive Mode

OPTIONS
-TRSJR Trailer
-Command Cut
-Dual Wheel Tires (Requires TRSJRW or TRSJRWB)
-Blade (option is for removal of standard blade)
-Pintle Hitch

This information is provided for informational purposes only. HDD Broker LLC cannot warrant the accuracy or completeness of this information. This information is subject to change by the manufacturer. Some specifications may vary by model year.

HDD Broker uses cookies and collects personal information on its websites.

To learn more, review HDD Broker's Privacy Policy and Cookie Policy. By clicking "I Accept", you indicate you have adjusted your browser settings to fit your preferences and consent to HDD Broker's use of cookies.

x